• Polski
  • English
  • Deutsch
  • Русский
Contact

PRESS CENTER

Archiwa Power engineering - POLNA S.A.

Central lubrication pump
PD 11 I 31*

The pump is designed to lubricate friction nodes in machines and devices through dosing distributors (two-way feeders). It is recommended for use in high-load machines and devices, with a large number of lubrication points located at long distances and requiring...
Read more

Central lubrication pump
PA 12*

The pump is designed for lubricating friction nodes in vehicle chassis and machines. Lubricant is fed to the reception point equipped with a ball nipple by a lubrication gun joined to the pump by a flexible hose. The pump is...
Read more

Central lubrication pump
PD 20 I PD 30*

The pump is designed to lubricate friction nodes in machines and devices through dosing distributors (two-way feeders). It is recommended for use in high-load machines and devices, with a large number of lubrication points located at long distances and requiring...
Read more

Central lubrication pump
PD 40

The pump is designed to periodically feed lubricant or oil to friction nodes in machines by means of two-way dosing units (dosing distributors). It is recommended for heavy duty machines and plants with up to 50 lubrication points, located at...
Read more

Control valves type Z

Applied in automatic and remote control installations as flow control elements to adjust flow of liquids and gases. Wide range of material and design versions make the valves widely sought-after in chemical industry, heat and power generation industry, paper industry,...
Read more

Control valves type Z1A-C1

This valve type is an efficient and durable solution for gas engineering deposit fluid systems, where erosion from solids reduces the life of valve internal components. High pressure drops and two-phase mixture also cause the possibility of cavitation. These hazards...
Read more

Control valves type Z33

Control valves type Z33 (previous name: BR33) represent one of the valve designs, where change in flow ratio is achieved through an eccentrically set rotary plug. Such structures are particularly useful for control of flow under heavy-duty conditions, with high...
Read more

Control valves type Z33 with piston and rotary actuators

Control valves type Z33 (previous name: BR33) are manufactured in configuration with membrane and spring rotary pneumatic actuators type R/R-99. The purpose of this proposal is to extend the offer of Z33 type valve actuators by rotary piston pneumatic and...
Read more

Direct acting pressure
regulator type ZSN 1

Regulators are used to control preset pressure in process installations connected to regulator valve outlet. They are used in district heating systems, industrial processes in water to control flow of cold and hot water, steam, air and non-combustible gases. Using...
Read more

Direct acting pressure
regulator type ZSN 3

Regulators are used to control preset pressure in process installations connected to regulator valve outlet. They are used in district heating systems, industrial processes in water to control flow of cold and hot water, steam, air and non-combustible gases. Using...
Read more

Direct acting pressure
regulator type ZSN 5

Regulators are used to control preset pressure in process installations connected to regulator valve outlet. They are used in district heating systems, industrial processes in water to control flow of cold and hot water, steam, air and non-combustible gases. Using...
Read more

Direct acting pressure
regulator type ZSN 7

Regulators are used to control preset pressure in process installations connected to regulator valve outlet. They are used in district heating systems, industrial processes in water to control flow of cold and hot water, steam, air and non-combustible gases. Using...
Read more

Double-ported globe control valves type Z10

Valves type Z10 (previous name: 10000 DG) with a pressure-balanced plug are used as final executive elements in automatic and remote control systems. They are used to regulate the flow rate of liquids and gases in the chemical industry, metallurgy,...
Read more

Filling pump PZ 40

The pump is designed to force plastic grease from barrels or other packages to tanks of central lubrication pumps type PA, PD and others. It may be used to fill other containers with plastic grease as well.
Read more

Four-way electromagnetic distributor ER*

The distributor is designed to change the direction of lubricant flow in the two-way central lubrication system. It is used in the lubrication system (in close proximity to the pump), in which the pump does not have a distributor.
Read more

Lance desuperheater type ST-1

Lance desuperheater is used in steam temperature control systems in industry and power engineering. The advantage of the desuperheater is excellent atomization of water and high regulation. We would also like to invite you to read the study concerning “Elements...
Read more

Loading pump PZ 20

The pump is designed to fill tanks of PR 14 type central lubrication pumps and other pumps with plastic grease. It may be used to fill other containers with plastic grease as well.
Read more

Lubrication gun SP 10 and hose WP 10

The lubrication gun (connected to the pump outlet by a hose) is used to supply grease to friction nodes, whose housings are equipped with ball or other grease nipples.
Read more

Lubrication pump MPS 10

The pump is designed for the lubrication with plastic grease or oil of machines and equipment requiring continuous lubrication in small quantities. The lubricant is fed to each receiving point via a separate line, directly from the pump. It is...
Read more

Lubrication station
type SA 1*

The station is designed for lubricating friction nodes in vehicle chassis and machines. Lubricant is fed to the lubrication point equipped with a ball nipple by a lubrication gun joined to the pump by a flexible hose.
Read more

Mesh filters for heat control valves type FS-1

Filters installed in front of control valves are designed to clean the medium flowing through them. They can be used in heating and other industries. We can adjust the control valve to match your individual needs. Filters installed in front...
Read more

Minimum flow valve type Z1B-M

Minimum flow valves are designed for use in recirculation systems of pumps supplying power boilers. They protect the pumps against hydraulic and thermal overload in case of low water consumption by the boiler, ensuring minimum flow in the bypass circuit...
Read more

Multi-spring diaphragm pneumatic actuators type P/R

Multi-spring diaphragm pneumatic actuators type P/R are used as control devices for control of control valves and other setting elements in industrial automation. They are made in the following varieties: simple action (air – stem extension) – type P reverse...
Read more

Multi-spring diaphragm pneumatic actuators type P1/R1

Multi-spring diaphragm pneumatic actuators type P1/R1 are used as control devices for control of control valves and other setting elements in industrial automation. They are made in the following varieties: simple action (air – stem extension) – type P1 reverse...
Read more

Needle valves type ZA

Needle valves are designed for assembly, start-up and maintenance of transducers, pressure gauges and other fixtures in measuring and automation regulatory installations. Depending on the design, needle valves perform the following functions: direct or remote instrument assembly, closing (opening) the...
Read more

Piston desuperheater type ST-1

The piston desuperheater is used for steam temperature control systems in industry and power engineering. The advantage of the desuperheater is excellent atomization of water and high regulation. We would also like to invite you to read the study concerning...
Read more

Pump with crane PZ 31

The pump is designed to force plastic grease from drums (barrels) of 200 dm3 capacity (acc. to BN-76/5046-03) to tanks of central lubrication pumps, e.g. type PA, PD and others. It may be used to fill other containers with plastic...
Read more

Pump with manual drive
PR 14

The pump is designed for periodical injection of plastic grease by means of dispensers (two-way dosing distributors) to cooperating surfaces in machines. It is recommended for use in machines and devices with lubrication points below 50, operating periodically and requiring...
Read more

Reduction and cooling stations

The reduction and cooling stations are applied in the commercial power industry for maintaining the pressure and temperature of steam within the limits determined by the technological process by injecting the cooling liquid. We would like to invite you to...
Read more

Ring Steam Desuperheater type SP-1

The cooling water is supplied to the injection nozzle(s) through the feeding flange stub pipe or with a welded connection. The amount of cooling water supplied to the steam pipeline is adjusted by changing its pressure at the inlet to...
Read more

SAS control unit*

The control device is designed to automatically and manually control the operation of two-way central lubrication systems and to signal their operating states and failures. Depending on the type, it can be used in lubrication systems with electromagnetic or hydraulic...
Read more

Single-ported globe control valves type Z1A

Applied in automatic and remote control installations as flow control elements to adjust flow of liquids, steam and gases. A wide range of material executions, high parameters in the range of pressures and operating temperatures, numerous design variants adapted to...
Read more

Single-ported globe control valves type Z1B

Applied in automatic and remote control installations as flow control elements to adjust flow of liquids, steam and gases. A wide range of material executions, high parameters in the range of pressures and operating temperatures, numerous design variants adapted to...
Read more

Single-ported globe control valves type Z1B-M

Applied in automatic and remote control installations as flow control elements to adjust flow of liquids, steam and gases. A wide range of material executions, high parameters in the range of pressures and operating temperatures, numerous design variants adapted to...
Read more

Stop valve type ZWZ 11 and ZWZ 12

Barrier valves are used in measuring systems for level gauges, flow meters and industrial automation. They enable, among other things, disconnection of the measuring installation directly at the tank, in which the medium level is measured, or at the measuring...
Read more

Three-way control valves type Z3

Applied in automatic and remote control installations as flow control elements to adjust flow of liquids and gases. Type Z3M is designed to mix two streams of medium, whereas type Z3R is designed to split one stream into two. Recommended...
Read more

Throttle valve type ZWD1

Throttle valves are used in measuring systems, heating equipment and industrial automation. They enable pressure throttling, flow rate regulation and total medium cut-off.
Read more

Two-line dispensers DD

Two-way feeders (dosing distributors) are designed to feed certain portions of lubricant to the lubrication points in machines and devices. They are component parts of two-way force feed lubrication systems.
Read more

Water distillers and water redistillers

Used for the purification of water containing dissolved mineral salts and gases by distillation Water-distillation apparatus Water purification of dissolved mineral salts and gases by distillation is possible owing to the use of DE5, DE10 plus, DE20 plus distillers and...
Read more

POLNA S.A.

ul. Obozowa 23 Str
37-700 Przemyśl
POLAND

TEL: +48 16 678 66 01
E-MAIL: sekretariat@polna.com.pl

KRS: NATIONAL COURT REGISTER: 0000090173 dated 12.02.2002 r. Provincial Court in Rzeszów, XII Division of National Court Register
COMPANY ID: 650009986     NIP: 795-020-07-05     BDO: 000030128
SHARE CAPITAL: 3.710.992,60 PLN
PAID CAPITAL: 3.710.992,60 PLN
BANK ACCOUNT NUMBER: 88 1030 1250 0000 0000 8901 4018 EUR SWIFT: CITIPLPX